WOx/TiO2光催化剂的可见光催化活性机理探讨

采用磁控溅射技术在用浸渍提拉法制得的TiO2薄膜上，溅射氧化钨层,通过气相反应中光催化降解二甲苯的实验表明，WOx/TiO2薄膜具有可见光活性.通过UV-Vis吸收光谱、X射线光电子能谱（XPS）等方法对其可见光活性的机理进行探索.UV-Vis吸收光谱表明WOx,TiO2对可见光响应的范围有一定的扩展,吸收强度增加.XPS表明WOx/TiO2薄膜表面形成了明显的W杂质能级和Ti缺陷能级,这是WOx/TiO2在可见光范围有一吸收的主要原因,也是光催化剂具有可见光活性的必要条件之一，同时杂质能级的存在使半导体费米能级上移,载流子增加,光催化效率提高.     

Thermal decomposition of the composite hydrotalcites of iowaite and woodallite

The thermal stability and thermal decomposition pathways for synthesized composite iowaite/woodallite have been determined using thermogravimetry analysis in conjunction with evolved gas mass spectrometry. Dehydration of the hydrotalcites occurred over a range of 56–70°C. The first dehydroxylation step occurred at around 255°C and, with the substitution of more iron(III) for chromium(III) this temperature increased to an upper limit of 312°C. This trend was observed throughout all decomposition steps. The release of carbonate ions as carbon dioxide gas initialised at just above 300°C and was always accompanied by loss of hydroxyl units as water molecules. The initial loss of the anion in this case the chloride ion was consistently observed to occur at about 450°C with final traces evolved at 535 to 780°C depending of the Fe:Cr ratio and was detected as HCl (m/z=36). Thus for this to occur, hydroxyl units must have been retained in the structure at temperatures upwards of 750°C. Experimentally it was found difficult to keep CO₂ from reacting with the compounds and in this way the synthesized iowaite-woodallite series somewhat resembled the natural minerals.     

三氯化镱催化丙烯酸酯与呋喃成环反应的研究

D iels-A lder反应具有立体专一性和很好的区域选择性,已被大量应用于天然有机化合物、香料、药物等的合成中。一般说来,D iels-A lder反应在加热条件下即能发生,但加热往往导致反应的区域选择性和立体专一性下降,而研究表明,路易斯酸催化下的D iels-A lder反应在不同程度上表现出或反应速度加快,或产率提高,或条件温和,尤其是区域选择性和立体专一性得到提高等良好特性。呋喃类化合物由于呋喃环所具有的芳香性而较难与一般的亲双烯发生D iels-A lder反应。如呋喃和丙烯酸甲酯在加热条件下反应2~3个月,产率只能达到50%,且反应温度的提高…     

Mesoporous micelle templated silica with incorporated C<Subscript>8</Subscript> and C<Subscript>18</Subscript> phase

Mesoporous silica material of MCM-41 type was synthesized by co-condensation of highly concentrated octyltriethoxysilane (OTEOS), octadecyltriethoxysilane (ODTEOS) and tetraethoxysilane (TEOS). The obtained hybrid materials were characterized using XRD, TG-DSC and low temperature adsorption/desorption of nitrogen. It was shown that the applied method of synthesis allows to obtain silica of MCM-41 type with a high degree of hydrocarbon saturation.     

Preparation of HPMC–EA–DMAEMA nanosized latex

Nanosized copolymer latex of hydroxypropylmethylcellulose (HPMC) grafted with ethyl acrylate (EA) and dimethylaminoethyl methacrylate (DMAEMA) has been prepared by acidifying submicron-sized latex particles synthesized by soap-free emulsion graft copolymerization using potassium persulfate (KPS) as initiator. The effects on the diameter of the latex particles of different conditions, for example concentration of DMAEMA, amount of HPMC, and ratio of HCl to DMAEMA for acidification, were investigated. It was found that increasing the mole ratio of HCl to DMAEMA to 1.0 and increasing the DMAEMA content both resulted in a decrease in particle diameter, whereas increasing the amount of HPMC resulted in larger particle sizes. Measurement by dynamic light scattering (DLS) revealed the diameter of the latex particles was >200 nm before acidification and <100 nm after acidification. Evidence of grafting was obtained by use of Fourier transform infrared (FTIR) spectroscopy. Transmission electron microscopy (TEM) was used to characterize the morphology of the copolymer particles before and after acidification.     

Influence of thermal and thermo-mechanical treatment

Two lipids with similar melting ranges but of different composition were analyzed using differential scanning calorimetry and X-ray diffraction. The lipids were processed via extrusion or were tempered at different temperatures; they were analyzed directly after extrusion and after storage at 40°C. Precirol ATO 5® showed high sensitivity to storage time and varied temperature exposure. Extrusion showed only marginal influences on the solid state. Melting peaks were narrower and shifted to higher temperatures in comparison to the untreated powder. Dynasan 114® was more robust, changes in the solid state could only be shown for samples treated above the melting range. Thus, Dynasan 114® is more appropriate for solid lipid extrusion of pharmaceutical products.